• Applicable for:  SPX5, SPX10, SPX30, SPXSOL, SPXCAN
  • Software Version: v3.05 & v4.00 (SPXCAN only)
  • Release Date: August 2012
  • Replaces: v3.00

Note: SPX-DI0 is not supported by this software.  Attempts to install the software below on a SPX-DI0 will render the pilot inoperable. The SPX-DIO is for for the Beneteau Dock & Go and Jeanneau 360 Docking systems.

Downloading the Software


Select the software update below depending on which Multifunction Display you will be using to perform the Remote Update. Please note if you have a G Series or a/c/e/gS Series you must check what version of software you have installed in the unit that you are using to perform the upgrade. For further information on this please click here.



Software for SPX5, SPX10, SPX30, SPXSOL


A Series C Series Classic E Series Classic C Series Wide E Series Wide G Series a/c/e/gS Series
A Series
DOWNLOAD		 C Classic
NOT AVAILABLE		 E Classic
DOWNLOAD		 C Wide
DOWNLOAD		 E Wide
DOWNLOAD		 G Series
v2 DOWNLOAD		 a/c/e/gS Series
v6 DOWNLOAD
          v4 DOWNLOAD v7 DOWNLOAD


View Update Instructions |  View Latest Manual



Software for SPX-CAN


A Series C Series Classic E Series Classic C Series Wide E Series Wide G Series a/c/e/gS Series
A Series
DOWNLOAD		 C Classic
NOT AVAILABLE		 E Classic
DOWNLOAD		 C Wide
DOWNLOAD		 E Wide
DOWNLOAD		 G Series
v2 DOWNLOAD		 a/c/e/gS Series
v6 DOWNLOAD
          v4 DOWNLOAD v7 DOWNLOAD

 

IMPORTANT TERMS OF DOWNLOADING SOFTWARE

 

This firmware update process is done at your own risk. Before initiating the update process be sure to backup and make copies of all important files. 

If the firmware process is interrupted your product may not function properly, therefore do not interrupt the process and ensure the unit is on a reliable power supply. Damage caused by incomplete upgrades will not be covered by Raymarine warranty. 

By Downloading the software, you agree to these terms.

 

Open Source GPL/LGPL

Some Raymarine products contain software code developed by third parties that are covered by open source GPL and LGPL software license agreements. You can view the third party license agreements by visiting the Manuals and Documents section of our website.

To access the open source GPL and LGPL licensed executables click here

 


Software History


Version Release Date Features
SPX5/10/30/SOL
v3.05

SPX-CAN
v4.00		 Aug 2012
  • Improved Compass Linearisation process:
    • Compass Linearisation is completed after two turns even if the message “Too Fast” or “Slow Down” is displayed.
     
  • Joystick operational fault corrected. (Previous software required Joystick to be connected via a ST1 to NG Converter):
    • Joystick now operates correctly connected directly to the Seatalk1 bus.
     
  • Compass heading now does not display if fluxgate has an error or is not connected. 
 
SPX5/10/30/SOL
v3.00		 March 2011
  • Alarm management has been enhanced and adds two new Alarms to inform the helmsman if the Pilot has erroneously dropped into Standby from any of the engaged modes. (E.g. Auto, Track, Vane, Pattern).
    • Autopilot Controllers and Pilot enabled MFD's connected on Seatalk 1 will alarm and display the following:
      • "PILOT RESET" - Autopilot resets due to an external event. (User presses Sleep switch, disables power or a faulty installation / wiring causing Course Computer to power cycle).
      • "PILOT S RESET" - Autopilot soft resets due to Pilot system internal error causing processor to reset.
  • Autopilot Controllers and Pilot enabled MFD's connected on Seatalk NG will alarm and display the following:
    • "DRIVE STOPPED" - Autopilot resets due to an external event. (User presses Sleep switch, disables power or a faulty installation / wiring causing Course Computer to power cycle).
    • "DRIVE STOPPED" - Autopilot soft resets due to Pilot system internal error causing processor to reset.
  • Pilot Data Tunnelling:
    • All Seatalk 1 Pilot commands and calibration data now tunnelled via the Seatalk to Seatalk NG Converter and decoded from Seatalk NG by the SPX Course Computer. This will now allow Seatalk 1 Controllers such as the ST6/7/8002 and the SmartController to be connected via the Converter to the Seatalk NG Backbone. (See example diagrams 2 below).
    • Compatibility Note:
      • The Seatalk to NG Converter software must be at level (v1.10) to function correctly. (TU454)
    • Installation Note:
      • The new SPX software will now detect a Pilot data loop and alarm "Seatalk Fail". Therefore avoid connecting both Seatalk Pilot Controllers via the Converter and Seatalk directly to the Course Computer.
 

SPX-CAN
v1.46

Aug 2008
  • SPX-CAN ONLY - Resolves Start-up Issue
 

SPX5/10/30/SOL
v1.20

April 2009
  •  
  • Power Steer Mode for Joystick use is now available in all Vessel Type Settings, including all Sail Boat modes.
  • Also incorporates the correction to Track mode released with (V1.19) when used with an MFD connected on Seatalk NG. This caused the pilot to automatically change onto the new waypoint before entering pre-track mode and confirmation.
 

SPX5/10/30/SOL

###

###
  • Initial Release
 

SPX-CAN
###

###
  • Initial Release